2026 Sydney price guide

Polished concrete cost in Sydney

Most Sydney floors cost $45 to $80 per m² for grind and seal, $80 to $150 for a mechanical polish, and $140 to $220 for high gloss. Use the estimator to see where your floor is likely to land, then read what pushes a price up or down.

Typical Sydney rates per square metre
Grind and seal$45 to $80 /m²
Mechanical polish$80 to $150 /m²
High gloss polish$140 to $220 /m²

Typical Sydney market ranges for 2026. These are a guide for budgeting, not a quote.

Estimate your floor

Length × width of each room, added together.

Finish
Stone exposure

Likely price for your floor

$4,800 to $6,200

Full market range: $2,700 to $4,800

    Get my exact price

    What typical Sydney floors cost

    The same three finishes on three common floor sizes. Read across a row to see how much the finish changes the bill, and down a column to see how size changes it.

    Typical Sydney price ranges by floor size, 2026
    FloorGrind and sealMechanical polishHigh gloss
    30 m²Kitchen and dining$1,350 to $2,400$2,400 to $4,500$4,200 to $6,600
    60 m²Open-plan living area$2,700 to $4,800$4,800 to $9,000$8,400 to $13,200
    120 m²Most of a single-storey home$5,400 to $9,600$9,600 to $18,000$16,800 to $26,400

    Small floors usually sit at the top of their range or above it, because the setup, travel and machine time are similar whether the job is 20 m² or 80 m². Big open floors usually sit lower.

    What moves the price of a polished concrete floor

    Two floors of the same size can be quoted thousands of dollars apart, and it's rarely the contractor making numbers up. These are the things that change the work involved.

    The condition of the slab

    A clean new slab that was protected during the build is the cheapest to polish. An older slab under tiles or carpet needs the glue, paint and old fillers ground off before polishing starts, and that's extra machine time with coarse tooling, which wears out fastest. Deep cracks, patched trenches and uneven areas add filling and extra passes.

    How big the area is

    Getting machines, vacuums and tooling to site and set up takes about the same time for a laundry as for a living area. On a small job that cost is spread over fewer square metres, so the rate per m² goes up. Doing several rooms in one visit is the simplest way to bring the rate down.

    How deep we grind

    Nil and salt and pepper exposure only cut into the top few millimetres. Full aggregate means grinding deeper into the slab to cut through the larger stones, and that takes more passes with coarse diamonds. It also reveals more air pockets and voids, which all need filling.

    How shiny you want it

    Each step up in sheen means more passes through finer grits. A satin floor finished at about 800 grit takes noticeably less time than a high gloss floor taken to 1500 or 3000. Grind and seal skips most of the refining altogether and relies on the sealer for its look, which is why it's cheaper.

    Access and the site

    Floor grinders are heavy. Ground-floor jobs with a driveway are straightforward. Upstairs rooms, apartments with lift bookings, narrow side paths and strict building hours all add time. Edges, steps, columns and lots of small rooms add hand work that a big machine can't do.

    What's included

    Crack repair, joint filling, moving furniture, removing old floor coverings, a penetrating guard and the final clean can each be included or charged as extras. This is where most of the gap between quotes comes from.

    Polished concrete or tiles: which costs more?

    On a slab you already have, polished concrete is usually cheaper than tiling at the same quality level, because you're not buying a new floor. In Sydney, laying floor tiles typically costs about $40 to $105 per m² in labour alone, and the tiles themselves add anywhere from $20 per m² for budget ceramic to $250 or more for natural stone. A mid-range porcelain floor ends up somewhere around $90 to $225 per m² before you add removal of old flooring, levelling or waterproofing.

    Grind and seal comes in under almost any tiled floor. A satin mechanical polish lands in the same range as a mid-range porcelain floor, and high gloss full aggregate costs about the same as good porcelain or a modest natural stone. Over the life of the floor, polished concrete has no grout to clean or reseal and no tiles to crack and replace, which narrows the gap further.

    Tiles still win in some places. Bathrooms and laundries need waterproofing and a floor graded to the drain, and tiles handle that better. If your slab is badly damaged or you want a very specific look, tiling over it may make more sense. We'll tell you if that's the case.

    How to keep the cost down

    The biggest saving is choosing the finish to suit each room. A satin polish in the living areas with grind and seal in the garage and laundry costs far less than high gloss throughout, and most visitors will never notice the difference in the rooms that matter less.

    Do as much of the floor as you can in one visit. Polishing three rooms together costs less per m² than polishing them a year apart, because setup is paid once.

    Clear the rooms before we arrive, and lift carpet yourself if you're comfortable doing it. Leave tile removal to someone with the right tools, though, because chipping tiles off by hand can gouge the slab and add repair work.

    If you're building, protect the slab. A few hundred dollars of floor protection during construction can save thousands in grinding out plaster, paint and glue later. Our polished concrete page explains how to plan a new slab for polishing.

    Get an exact price for your floor

    An estimate can only go so far. At a free on-site measure we check the slab, grind a small test patch so you can see the stone, and give you a fixed written price with every item listed.

    Prefer to talk it through? Call 02 5850 4790.

    Book your free measure

    We reply within one business day.

    No obligation. We only use your details to reply to you. Privacy policy

    Cost questions

    Why do polished concrete quotes vary so much?

    Usually because they're quoting different floors. One quote might be a grind and seal while another is a true mechanical polish, or one might include crack repair, edges and glue removal while another lists them as extras. Ask each contractor to name the process, final grit, exposure and products, then compare line by line.

    Is there a minimum charge for small jobs?

    Many concrete polishing contractors set a minimum charge, because a small room needs the same machines, setup and travel as a large one. If you only have a few square metres, ask about the minimum before comparing per-m² rates, and consider adding a second area to the same visit.

    Do the prices on this page include GST?

    They're typical Sydney market ranges, and contractors don't all quote the same way. Always check whether a quote includes GST before comparing it with another. Our written quotes state it clearly.

    Is grind and seal a cheaper version of polished concrete?

    It's a different finish rather than a cheaper copy. Grind and seal gets its look from a sealer coating, so it costs less upfront but needs resealing in busy areas every few years. A mechanical polish costs more upfront and has no coating to wear through. Our grind and seal page explains when each one makes sense.

    How much does it cost to polish a garage floor?

    Garages are usually done as grind and seal, often with an anti-slip additive in the sealer, so the $45 to $80 per m² range applies. A double garage of about 36 m² would typically fall around $1,600 to $2,900. Oil stains, old paint and cracks add to that. Where a garage doubles as a workshop, epoxy flooring is worth comparing.

    Call now Free quote